-00 02-3 1. ENGINE ASSEMBLY Unit Cylinder head Height Flatness Valve protrusion Intake valve Exhaust valve Flatness on manifold Intake manifold side Exhaust manifold Connecting rod Camshaft End play Axial end play Intake Exhaust Camshaft position Distance between Camshaft position sensor sensor and sprocket Valve Clearance between valve and piston Valve recess Intake Exhaust Intake Exhaust Cylinder block Piston ring Piston protrusion TOP ring end gap 2nd ring end gap 3rd ring end gap Offset Head gasket Piston protrusion 0. to 0. to 0. to 0. Description Specification .9 to .1 mm below 0.1 mm 0.6 to 1.0 mm 0.6 to 1.0 mm 0. mm 0. mm 0....
-01 03-3 1. SPECIFICATIONS Description Fuel Fuel filter Type Filter type Change interval EU GEN Water separation interval EU GEN Specification Diesel Fuel heater + priming pump + water separator integrated type Changeable filter element type every , km every , km every , km every , km cc W .5V bar Eccentric cam/Plunger type Gear driven type - ~ °C bar - ~ °C Vane type 0.5 : bar L Plastic Single sender type Water accumulating capacity Heater capacity Injector High pressure fuel pump System pressure Type Operating type Normal operating temperature Operating pressure Operating temperature Low pressure fuel pump Type Gear ratio (pump...
-00 04-3 1. SPECIFICATIONS Unit Description Filter type Air cleaner element Initial resistance Service interval Specification Dry, filter element Max. mmAq EU: Change every , km GEN: Change every , km Air cleaner assembly Weight Operating temperature Radiation Pressure loss at turbocharger Intercooler Cooling type Core size Core type Air cooled type W* H*70T C/FIN 2.36kg - ~ over , Kcal below mmHg * Shorten the service interval under severe conditions such as driving on a dusty road or off-road. ...
-01 05-3 1. MAJOR CHANGES Muffler Assembly - Muffler assembly parts (A, B) changed due to change of rear subframe (A) Connecting pipe between muffler and tail silencer: moved by mm (B) Gap between tail silencer pipe and body: changed from mm to mm ...
-00 07-3 1. SPECIFICATION Unit Oil pump Lubrication system Type Capacity Relief pressure Oil filter Engine oil Type Specified oil Capacity (L) Service interval EU Specification Gear pump, forced circulation Inscribed gear L at 4, rpm 5.8 bar 0.3 bar Full flow/Paper element SAE 5W (approved by MB SHEET .51) Min.: 4.5 L / Max.: 6.0 L Change every , km or months (The service interval should be shortened under severe conditions) Change every , km or months (The service interval should be shortened under severe conditions) Piston 1.5bar 1.0bar L/min bar General Oil injection nozzle Type Operating pressure Closing pressure Oil fl...
-00 08-3 1. SPECIFICATION Description Cooling system Coolant Radiator Type Capacity Core size Flow type Type Antifreeze Mixing ratio (water:antifreeze) Motor type Cooling fan module Motor weight Control type Fan runout Capacity Coolant reservoir Circulation Pressure cap Pressure Type Opening temperature Thermostat Fully open temperature Valve lift Specification Water cooling, forced circulation approx. .5 L W x H x T (over 3, cmІ) Cross flow SYC (Long life coolant) : DC motor 2. kg PWM type mm over 1.5 L Closed roof type Screw type 1.4bar Wax pallet type mm ...
-00 10-3 1. SPECIFICATIONS Description Glow plug Rated voltage Max. temperature Operating temperature Resistance Glow plug control unit Operating voltage Operating temperature Dark current Specification 4.4 V °C °C ~ °C °C: 0. ~ 0. ~ V -40°C ~ °C Max. mA ...
-01 11-3 1. SPECIFICATION Description Capacity Engagement Rotating direction Pinion gear manufacturing Solenoid operating voltage Weight Bracket manufacturing Specification V 2.3kW Meshed type Clockwise Cooled forging Max. V 2.5 kg Aluminum die casting ...
-23 12-3 1. CRUISE CONTROL SWITCH The cruise control is an automatic speed control system that maintains a desired driving speed without using the accelerator pedal. The vehicle speed must be greater than km/h to engage the cruise control. This feature is especially useful for motorway driving. The cruise control system is a supplementary system, which helps the driver to drive the vehicle at a desired speed without using the accelerator pedal under the traffic condition where the vehicle-tovehicle distance meets the legal requirement. ...
-00 13-3 1. SPECIFICATION Item E-EGR valve Motor EGR response time Driven by Valve Position sensor EGR gas flow rate Sensing type Supplied voltage Maximum signal range Maximum power consumption E-EGR cooler Cooling capacity Cooling fin type Cooler type E-EGR bypass valve Driven by Specification ms DC motor Kg/h Hole sensor 5V % 5% ~ % mA 8.3 kW or more Wavy fin U-shaped Vacuum (Solenoid valve) ...
-02 14-3 1. CAUTIONS 1) Standard pattern of soot accumulation Abnormal Soot Accumulation Normal Soot Combustion Cautions to protect the catalyst filter Use the designated fuel only. Observe the recommended service intervals of engine oil. Check the engine oil level frequently and add if necessary. Do not idle the vehicle unnecessarily. Do not turn off the engine while the vehicle is running. Do not shift the gear selector lever to neutral when going downhill. Do not use improper engine oil or fuel additives. Do not drive for a long time when the warning lamp is illuminated. Make sure no flammable material, such as dry grass ...
-00 15-3 1. ENGINE DATA LIST Data Coolant temperature Intake air temperature Idle speed Engine load Mass air flow Throttle position angle Engine torque Injection time Battery voltage Accelerator pedal position Accelerator pedal position Throttle position Throttle position Oxygen sensor A/C compressor switch Full load Gear selection (A/T) Knocking control Brake switch Cruise control Unit rpm % kg/h °TA Nm ms V V V V V V 1=ON / 0=OFF 1=ON / 0=OFF 1=ON / 0=OFF 1=ON / 0=OFF 1=ON / 0=OFF 1=ON / 0=OFF Value ~- - to (varies by ambient air temperature or engine mode) (P/N) ~25% to kg/h 0° (Full Open) to ° (Close) varies by engine conditions...
-22 03-3 1. FUEL SYSTEM SPECIFICATION Use Only Unleaded Fuel Rated at Octane or Higher Fuel quality and additives contained in fuel have a significant effect on power output, drivability, and life of the engine. Fuel with too low an octane number can cause engine knock. Do Not Use Methanol Fuels containing methanol (wood alcohol) should not be used in vehicle. This type of fuel can reduce vehicle performance and damage components of the fuel system. Vehicle Fueling from Drums or Storage Containers For safety reasons (particularly when using noncommercial fueling systems) fuel containers, pumps and hoses must be properly ear...
-01 05-3 1. OVERVIEW OF EXHAUST SYSTEM - When you are inspecting or replacing exhaust system components, make sure there is adequate clearance from all points on the underbody to avoid possible overheating of the floor panel and possible damage to the passenger compartment insulation and trim materials. Check the complete exhaust system and the nearby body areas and trunk lid for broken, damaged, missing or mispositioned parts, open seams, holes, loose connections, or other deterioration which could permit exhaust fumes to seep into the trunk may be an indication of a problem in one of these areas. Any defects should be corrected im...
-23 10-3 1. CRUISE CONTROL SWITCH The cruise control is an automatic speed control system that maintains a desired driving speed without using the accelerator pedal. The vehicle speed must be greater than km/h to engage the cruise control. This feature is especially useful for motorway driving. The cruise control system is a supplementary system, which helps the driver to drive the vehicle at a desired speed without using the accelerator pedal under the traffic condition where the vehicle-tovehicle distance meets the legal requirement. ...
-02 01-3 1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS - Disconnect the negative cable from the battery in advance when working on electrical units. Make sure to turn "OFF" the ignition switch and other lamp switches before disconnecting or connecting the negative battery cable. (Otherwise, semiconductor parts can be damaged.) - Do not drop or appy excessive impact to sensors and relays. 80 - If a fuse is blown, replace it with a fuse which has the correct amperage rating. If you use a fuse with higher capacity than the specification, the component can be damaged or catch fire. 10A 15A ...
-01 02-3 1. SPECIFICATIONS OF RK - STICS 1) Electrical Performance Item Rated voltage Operating voltage Operating temperature Reserved temperature Max. operating humidity Resistible voltage Insulating resistance Parasitic current Requirement DC V DC to V - ~ + - ~ + % V No heat and fire due to Confined with PCB, waterproof and coating that the current leaks. requires the insulation. below 4.0 mA (below 6.0 mA) below 1.2 V below 2.0 V IGN = OFF, Full output load = OFF, seconds (after received the signals), No input changes for seconds Pin no. and 2, 3, 5, 7 Pin no. and 1, Should operate normally within this range. Remark Volt...
-06 03-3 1. SPECIFICATIONS Item Item Operating voltage (CAN) Operating temperature Immobilizer unit Coil inductance Modulation method Frequency Frequency Transponder Operating temperature Transponder coding Specification 6.0 V to .0 V (6.0 V ~18.0 V) - ~ uH uH FSK (Frequency Shift Keying : frequency displacement) .2 KHz KHz .2 KHz KHz - ~ + Up to 5 2. CAUTIONS 1. The vehicle owner must observe the service works when deleting the transponder codes or registering additional keys. 2. In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to remove it and damage the system, starting will be imposs...
-01 04-3 1. SPECIFICATIONS 1) Power, Voltage, Current Description Rated voltage Operating voltage Inspection voltage Operating temperature Standard Black face Storage temperature Performance guarantee voltage Dark current Standard Black face Specification DC V DC 9V ~ V DC .5V -30°C ~ +75°C (while driving) -30°C ~ +80°C -40°C ~ +85°C DC V ~ V below 3mA (12V, °C), Stabilized conditions (standby mode) around seconds after IGN OFF below 1mA (12V, °C), Stabilized conditions (standby mode) around seconds after IGN OFF ...
-01 07-3 1. BULB SPECIFICATIONS Description Exterior lamp Headlamp High beam + DRL Low beam Turn signal lamp Position lamp Front fog lamp Side repeater Rear combination lamp Rear fog lamp License plate lamp High mounted stop lamp Interior lamp Front room lamp Glove box lamp Door courtesy lamp Side room lamp Rear room lamp Tail (stop) lamp Turn signal lamp Back-up lamp Amount Specification (EU) W + W W W 5W H W 5W(21W) W W W 5W 5W 5W 5W 5W 5W 5W Specification (General) W ...
-00 06-3 1. SPECIFICATIONS 1) Center Fascia Switch Item Hazard warning flasher switch Windshield heated glass switch Center fascia switch & bezel assembly Rear heated glass switch ESP OFF switch Driver/front passenger seat warmer switch Fog lamp switch DC V A(inductive load) Specifications DC V A(lamp load) 2) 4WD Switch & HLLD Switch & Rear Wiper Operation Switch Item Washer switch 4WD switch & HLLD switch & rear wiper operation switch assembly Wiper switch 4WD switch HLLD switch Specifications DC V 3.8 A(lamp load) DC V 3.0 A (max. A) DC V mA DC V A (inductive load) 3) Steering Wheel Switch Item Steering wheel switc...
-11 08-3 1. SYSTEM LAYOUT AND OVERVIEW The rain sensing wiper unit in this vehicle doesn’t control the wiper directly. The rain sensing unit detects the amount of rain drops and sends the operating signal to STICS, and STICS drives the wiper directly. Rain sensing unit Multifunction wiper switch: AUTO and sensitivity control A sensor that emits infrared rays through LED and then detects the amount of rain drops by receiving reflected rays against sensing section(rain sensor mounting section on the windshield)with photodiode. AUTO : Wiper operates automatically by rain sensor FAST SLOW : Auto delay/Auto speed control. A positio...
-01 09-3 1. SPECIFICATIONS FOR PAS Item Item Rated voltage Operating voltage Operating temperature PAS unit Maximum humidity High internal pressure Insulation resistance Max. permissible current Operating frequency Detection range Tolerance Operating voltage range Specification DC .6 V (IGN power) DC 9.0 V ~ .0 V - ~ + % V No heat & fire due to current leak Unit: mA or less Sensor: mA or less KHz cm~ cm (based on lineal distance between sensor and obstacle) cm DC V PAS sensor ...
-05 11-3 1. SPECIFICATION 1) Audio Head Unit Item Audio Voltage Operating voltage Output Current consumption Leakage current Radio Frequency Specification DC .4V DC .8V~16.0V W/1ch 4ch A or less Up to A mA or less FM: .5~ MHz AM: ~ KHz MW: ~ KHZ LW: ~ KHZ FM1: 6ch FM2: 6ch AM: 6ch MW : 6ch LW : 6ch AM: dBu FM: dBu AM: dB FM: dB FSTN 9.0V VDD: 3.0~3.3V - ~ + - ~ + X MD-5XR (Bluetooth multimedia module) Bluetooth 2.0+EDR (Enhanced Data Rate) Supports HFP, A2DP, AVRCP profile formats (HFP, A2DP: profile for calling) (AVRCP: profile for listening music) Preset Usable sensitivity S/N raito (limit value) LCD Type Operating voltag...
-01 01-3 1. SPECIFICATIONS W5A (2WD) / W5A (4WD) Item Input torque Diameter( Torque converter) Lockup function Gear ratios 1st 2nd 3rd 4th 5th Reverse: S mode / W mode Driving type Fluid specification Fluid capacity Selected lever indication Parking lock system Reverse lock system Selected lever indication Oil temperature sensor TCU Shift solenoid valve(25) Resistance Operating distance Operating current P.R.N.D 1, 2, 3, 4, Resistance: R, D Resistance: P, N P.R.N.D D+/DSpecification Nm mm Yes 3. /1. WD(4WD) Shell ATF approx. Mechanical Electrical Brake switch(signal) TGS lever CAN TGS lever Lever position CAN 0.5 ~ 2.5 k k EGS 2 mm...
-01 02-3 1. SPECIFICATION Description Basic structure Gear ratio 1st 2nd 3rd 4th 5th 6th Reverse Synchronizer ring type 1st 2nd 3rd 4th 5th 6th Reverse Shifting Type Gear selector lever position Transmission fluid Type Capacity Service interval Specification 2-shaft, 6-speed (directly connected gears) 4. : . : . : . : . : . : . : T: Triple-cone T: Triple-cone T: Triple-cone S: Single-cone D: Double-cone S: Single-cone T: Triple-cone Floor change type Reversing: High-force type HD MTF W/ (SHELL) or HK MTF W/85(SK) 2.2 Inspect and replenish every km or years (under severe driving conditions, change every , km) What’s the severe con...
-00 03-3 1. SPECIFICATION Description Operating type Clutch pedal Type Max. operating travel Pedal height Pedal free play Clutch disc Type Diameter of facing Numbers of disc Thickness of disc Setting load of clutch cover assembly Clutch master cylinder Concentric slave cylinder Clutch fluid Operating travel Inner diameter Maximum operating travel Operating pressure Type Capacity Specification Hydraulic type Suspended type mm . mm ~ mm Dry type single diaphragm Outer: Ш mm Inner: Ш mm Free: 8. .3 mm When loaded: 8. .2 mm At least 7, N .0 mm Ш . Max. mm Max. 2, N DOT As required ...
-01 04-3 1. SPECIFICATIONS Front Axle Description Drive shaft type Axle housing type Differential Type Gear type Final gear reduction ratio Engine + M/T Engine + A/T Oil Capacity Specification Specification CV joint Build up Conventional type Hypoid Gear 4. .2 L SAE W / , API GL-5 Rear Axle Description Axle shaft type Axle housing type Differential Type Gear type Final gear reduction ratio Engine + M/T Engine + A/T Oil Capacity Specification Specification Semi-floating Build up Conventional type Hypoid Gear 4. .5 L TOTAL-ISU EP-B W/90 ...
-01 05-3 1. SPECIFICATIONS Description Total length Weight Oil capacity Oil type Location Major element Housing Bolt Input shaft Specifications mm .4 kg (including oil) 1.4 L ATF DEXRON II or III Transfer case Part-time EA, M8 x 1. A/T: outer spline ...
-01 06-3 1. SPECIFICATIONS Description Structure Front propeller shaft (4WD) Rear propeller shaft Run-out Unbalance Length of front propeller shaft Length of rear propeller shaft 4WD A/T M/T 2WD 4WD A/T A/T Specification Universal joint with yoke arm and spider and CV joint One universal joint and one CV joint Two universal joint and one CV joint below 0.4 mm Max. g·cm / 4, rpm 0 mm 0 mm 0 mm 0 mm ...
-01 07-3 1. SPECIFICATIONS Description Front Suspension Suspension type Spring type Shock absorber type Stabilizer bar type Double wishbone Coil spring Reciprocating cylindrical type (gas type) Torsion bar type Specification Rear Suspension Multi-link type Coil spring Reciprocating cylindrical type (gas type) Torsion bar type 2. WHEEL ALIGNMENT Toe-in Front Wheel Alignment Camber Caster Toe-in Rear Wheel Alignment Camber Caster 0.°0.10° -0.12°0.50° 4.80°0.50° 0.48°0.15° -1.20°0.50° - ...
-03 08-3 1. SPECIFICATIONS Description Front brake Rear brake Master cylinder Brake booster Type Type Type Type Operating type Brake oil Grade Service interval Specification Ventilated disc Ventilated disc Step feed bore tandem, double cylinder Tandem type (integrated level sensor) Foot operated type DOT Replace every years ...
-01 09-3 1. SPECIFICATIONS Description Unit HECU (Hydraulic & Electronic Control Unit) ABS CPU:MCU (32bit) Clock Frequency: MHz Memory: ~ KB ESP CPU:MCU (32bit) Clock Frequency: MHz Memory: ~ KB Location Under the front washer reservoir On each wheel Front air gap: 0.3 ~ 1.3mm, Rear air gap: 0.3 ~ 1.3 mm Under the steering wheel Wheel Speed Sensor Active type wheel speed sensor Active type wheel speed sensor Steering Wheel Angle Sensor N/A Maximum angular speed: °/sec Operating voltage: 9~ V Integrated with yaw rate sensor and lateral sensor Analog output Sensor Cluster Pressure Sensor N/A Under the aud...
-01 10-3 1. SYSTEM OVERVIEW When braking suddenly or braking on slippery roads, the vehicle keeps moving forward but the wheels are locking and not rotating. If these happen, the vehicle may lose stability or rotate resulting in an accident. ABS helps to maintain directional stability and control of the vehicle. ABS is designed to secure more safety and increase the control of steering wheel during emergency braking situation. But, ABS does not guarantee perfect safety beyond its physical limit. ABS in this vehicle contains EBD function. In normal driving conditions, the brake system operates without ABS function. 1) Basic Theory...
-01 12-3 1. SPECIFICATION Description Tire inch inch Tire inflation pressure Wheel inch inch Balance weight Tightening torques of wheel bolt Wheel offset 2WD 4WD Specification /65R /60R psi 6.5JX .0JX Inner: Clip-on type Outer: Tape type .4 to .8 Nm mm mm ...
-30 01-3 1. SPECIFICATION Item Rated voltage Operating voltage A/C controller Current consumption Operating temperature Dark current Diameter of pulley A/C compressor Rated voltage Current consumption Refrigerant fluid Condenser Receiver drier Size Moisture absorbent Pressure switch Heating capacity Front heater & A/C module Cooling capacity Expansion valve Rear heater & A/C module Refrigerant Heating capacity Cooling capacity type Volume PTC heater Material Power consumption FATC DC V DC to V 2A -30~ mA or less mm DC V 2.2 A PAG RL cc .8wX .6hX16.0t XH-9 Refrigerant pressure sensor Kcal/hr Kcal/hr Block type Kcal/hr Kcal/hr R a g g...
-03 02-3 1. SPECIFICATIONS Description Item Operating voltage Voltage for diagnosis and selfdiagnosis Air bag unit (SDM) Operating temperature Storage temperature Overvoltage protection Ground resistance Driver/passenger air bag module Seat air bag module Seat belt pretensioner Operating voltage Operating voltage Side impact sensor voltage Operating voltage Specification .0 V to .5 V 8.0 V to .5 V - ~ - ~ V m or less 8.0 V to .5 V .0 V to .5 V 8.0 V to .5 V .0 V to .5 V If you measure the air bag module using a multitester, the air bag module may be deployed, causing a personal injury. Never use the multitester to check the air b...
-01 03-3 1. SPECIFICATION Item Tilt Up/down Reclining Folding Sliding Seat warmer Front Seat ° mm ( mmx3) ° (2°x40) mm ( + mm) Rear 1st Row Seat mm ( mmx5) ° (2°x38) ° mm ( + mm) Rear 2nd Row Seat mm ( mmx6) ° (2°x38) ° mm ( + mm) Rear 3rd Row Seat mm ( mmx6) ° - Headrest Seat 2. WARNINGS FOR POWER SEAT 1. Adjust the driver's seat before driving. 2. Make sure that the seat is firmly secured after adjusting. 3. Never drive the vehicle with the head restraint removed or lowered excessively. Otherwise, your neck, spine or other parts of the body can be severely injured in the event of an accident. If you recline the seatbac...
-00 04-3 1. SPECIFICATIONS Item Operating voltage Stand by current Specification ~ V Max. mA Max. mA Load current Operating temperature Storage temperature 6A A - ~ - ~ Open, close: max. sec Operating time Open, close: max. sec Tilt: max. 1.5 sec Tilt: max. sec 1st step sliding open: mm Glass open level 2nd step sliding open: mm Tilt up & open: . mm Glass thickness Displacement .2 mm 2L / min - - IGN ON Sleep mode Normal operation Max. load current Details ...
