Документация на пробразователи частоты серии F5 фирмы KEB
Сервопривод KEB F5 SERVO в корпусе A (A-SERVO) нструкция по установке.
COMBIVERT The general EMC and safety directions at www. keb.de have to be observed !
Сервопривод KEB F5 SERVO в корпусе A (A-SERVO) нструкция по установке.
COMBIVERT
The general
EMC and safety
directions at www.
keb.de have to be
observed !
Installation Manual Housing A
Mat.No. Rev.
00F5SEM-KA J
This manual describes the KEB COMBIVERT F5. Particular attention is paid to the installation,
the connection as well as the basic operation. Due to the various application and programming
possibilities, the application-specific connection and/or wiring diagram, the parameter adjustment
as well as instructions to the start-up are to be taken from the documentation of the machine
manufacturer.
A list of instruction manuals and documents giving assistance for the construction, documentation
and service is provided at the end of this manual. The safety and warning notes listed in this in-
struction manual as well as in other documentation must be observed at any rate to ensure a safe
operation. Non-observance of the safety instructions leads to the loss of any liability claims. The
safety and warning instructions specified in this manual do not lay claim on completeness. KEB
reserves the right to change/adapt specifications and technical data without prior notice. The used
pictograms have following significance:
Danger
Is used, if life or health of the user are endangered or substantial
Warning
damage to property can occur.
Caution
Attention
Is used, if a measure is necessary for safe and trouble-free ope-
observe at
ration.
all costs
Information
Is used, if a measure simplifies the handling or operation of the
Aide
unit.
The information contained in the technical documentation, as well as any user-specific advice in
spoken and written and through tests, are made to best of our knowledge and information about
the application. However, they are considered for information only without responsibility. This also
applies to any violation of industrial property rights of a third-party.
Inspection of our units in view of their suitability for the intended use must be done generally by the
user. Inspections are particulary necessary, if changes are executed, which serve for the further
development or adaption of our products to the applications (hardware, software or download
lists). Inspections must be repeated completely, even if only parts of hardware, software or down-
load lists are modified. Original spare parts and authorized accessories by the manufacturer serve
as security. The use of other parts excludes liability for the damages which can result from it.
Application and use of our units in the target products is outside of our control and therefore exclu-
sively in the area of responsibility of the user. Repairs may only be carried out by the manufacturer
or an authorised repair agency. Unauthorised opening and tampering may lead to bodily injury and
property damage and may entail the loss of warranty rights.
GB -
Table of Contents
1. Safety and Operating Instructions
2. Product description.5
2. Intended use.5
2. Unit identification
2. Technical data
2. Dimensions and Terminals.9
3. Installation and Connection
3. Control cabinet installation.10
3. EMC-conform Installation.10
3. Connection of Power Circuit.
3.3. Wiring instructions
3.3. Terminal Strip X1A
3.3. Mains connection.12
3.3. Motor connection with terminal strip X1B.12
3.3. Connection of the temperature monitoring.13
3.3. Connection of a braking resistor with temperature monitoring in accordance with UL.14
3. Encoder interface connection.14
3.4. Resolver connection at KEB motors with connector X3A.14
3.4. Incremental encoder input / -emulation X3B
3. Control board Servo.16
3.5. Control terminal strip X2A.16
3.5. Connection of the control terminal strip
4. Operation of the Unit
4. Operation Accessories.18
4.1. With HSP5 cable and without operator
4.1. Digital operator (part number F - )
4.1. Interface operator (part number F - )
4.1. Remote control
4.1. Other operators
4. Keyboard Operation.19
4.2. Parameter numbers and values.19
4.2. Resetting error messages
4.2. Password Input.20
4. Parameter description for F5 servo
A. Annex A.25
A. Overload characteristic.25
A. Calculation of the motor voltage.25
A. Maintenance.25
A. Storage.26
A. Changing the response threshold of the braking transistor
B. Annex B.28
B. CE-Marking
B. UL Marking.28
B. Additional Manuals.31
GB - 3
Important, absolutely read
1. Safety and Operating Instructions
Safety and Operating Instructions
for drive converters
(in conformity with the Low-Voltage Directive /95/EC)
1. General (potential health risks).
In operation, drive converters, depending on their degree of. Electrical connection
protection, may have live, uninsulated, and possibly also moving
When working on live drive converters, the applicable national
or rotating parts, as well as hot surfaces.
accident prevention rules (e.g. VBG 4) must be complied with.
In case of inadmissible removal of the required covers, of improper
The electrical installation shall be carried out in accordance
use, wrong installation or maloperation, there is the danger of
with the relevant requirements (e.g. cross-sectional areas of
serious personal injury and damage to property.
conductors, fusing, PE connection). For further information, see
For further information, see documentation. documentation.
All operations serving transport, installation and commissioning Instructions for the installation in accordance with EMC require-
as well as maintenance are to be carried out by skilled technical ments, like screening, earthing, location of filters and wiring, are
personnel (Observe IEC or CENELEC HD or DIN VDE contained in the drive converter documentation. They must always
and IEC or DIN/VDE and national accident be complied with, also for drive converters bearing a CE marking.
prevention rules!). Observance of the limit values required by EMC law is the respon-
sibility of the manufacturer of the installation or machine.
For the purposes of these basic safety instructions, „skilled
technical personnel“ means persons who are familiar with the. Operation
installation, mounting, commissioning and operation of the
Installations which include drive converters shall be equipped
product and have the qualifications needed for the performance
with additional control and protective devices in accordance with
of their functions.
the relevant applicable safety requirements, e.g. act respecting
2. Intended use technical equipment, accident prevention rules etc Changes
to the drive converters by means of the operating software are
Drive converters are components designed for inclusion in elec-
admissible.
trical installations or machinery.
After disconnection of the drive converter from the voltage supply,
In case of installation in machinery, commissioning of the drive
live appliance parts and power terminals must not be touched
converter (i.e. the starting of normal operation) is prohibited until
immediately because of possibly energized capacitors. In this
the machinery has been proved to conform to the provisions of
respect, the corresponding signs and markings on the drive
the directive /42/EC (Machinery Directive). Account is to be
converter must be respected.
taken of EN.
During operation, all covers and doors shall be kept closed.
The drive converters meet the requirements of the Low-Voltage
directive /95/EC. The harmonized standards of the series. Maintenance and servicing
EN -5-1 for the drive converters were used.
The manufacturer’s documentation shall be followed.
The technical data as well as information concerning the supply
KEEP SAFETY INSTRUCTIONS IN A SAFE PLACE!
conditions shall be taken from the rating plate and from the docu-
mentation and shall be strictly observed.
3. Transport, storage
The instructions for transport, storage and proper use shall be
complied with.
The climatic conditions shall be in conformity with EN -
5-1.
4. Installation
The installation and cooling of the appliances shall be in accor-
dance with the specifications in the pertinent documentation.
The drive converters shall be protected against excessive strains.
In particular, no components must be bent or isolating distances
altered in the course of transportation or handling. No contact shall
be made with electronic components and contacts.
Drive converters contain electrostatic sensitive components
which are liable to damage through improper use. Electric
components must not be mechanically damaged or destroyed
GB -